MAX713 i Energizer NH12



Masz problem? Zapytaj na forum elektroda.pl

Poprzedni Następny
Wiadomość
Spis treści
From: "szlovak" <adamkxBEZx_at_nospam_o2.pl>
Subject: MAX713 i Energizer NH12
Date: Mon, 10 Apr 2006 14:10:45 +0000 (UTC)


Witam

czy ten układ może ładowac ten akumulatorek? Wiadomo, max713 czeka aż
napiecie na akumulatorku zacznie maleć (chyba o 5mV). Szukałem pdfa i
nie znalazłem. Energizer nie daje tej informacji czy można tak ładować.
orientuje się ktoś w tym temacie?

--
pzdr

Poprzedni Następny
Wiadomość
Spis treści
From: "darnok" <darnok-allegroMALPAwpKROPKApl_at_nospam_anty.spam.ch>
Subject: Re: MAX713 i Energizer NH12
Date: Mon, 10 Apr 2006 16:11:53 +0200


In news:e1dp15$hb3$1_at_nospam_nemesis.news.tpi.pl, szlovak wrote:
Witam

czy ten układ może ładowac ten akumulatorek? Wiadomo, max713 czeka aż
napiecie na akumulatorku zacznie maleć (chyba o 5mV). Szukałem pdfa i
nie znalazłem. Energizer nie daje tej informacji czy można tak
ładować. orientuje się ktoś w tym temacie?

Slabo szukales - bardzo slabo:
http://pdfserv.maxim-ic.com/en/ds/MAX712-MAX713.pdf

--
darnok


Poprzedni Następny
Wiadomość
Spis treści
From: "szlovak" <adamkxBEZx_at_nospam_o2.pl>
Subject: Re: MAX713 i Energizer NH12
Date: Mon, 10 Apr 2006 18:48:34 +0000 (UTC)



Slabo szukales - bardzo slabo:
http://pdfserv.maxim-ic.com/en/ds/MAX712-MAX713.pdf

Słabo czytałeś, bardzo słabo. Tego pdfa już mam od dawna i on nie
zawiera tych danych , bo są specyficzne dla marki ogniw. Otóż możliwe
że jedne akumulatorki NiMH nie są równe innym , szczególenie że te NH12
to AAA czyli mniejsze. Więc moze im nie odpowiadać taki typ ładowania.
Dlatego też jest MAX712.

Więc pytanie czy te akumulatorki AAA 850mAh może ładować max713 jest
nadal aktualne.

--


Poprzedni Następny
Wiadomość
Spis treści
From: "Slavek" <slavek.p_at_nospam_gmail.com>
Subject: Re: MAX713 i Energizer NH12
Date: 10 Apr 2006 12:39:56 -0700


nickel_metal_hydride_app.pdf
na ich stonach mowi o tym :
Two-Stage-This approach uses a timer to switch from the initial
charge rate to the maintenance
charge rate. Because there is no sensing of the cell's transition
into overcharge, the charge rate
must be kept low (0.1C) to minimize overcharge-related impact on cell
performance and life.
Charge durations are typically set at 16 to 24 hours to ensure full
recharge in cases of complete
discharge. Although economical, since this scheme makes no allowance
for the degree of
discharge or for environmental conditions, its use is rarely
recommended for typical nickel-metal
hydride applications.
Three-Stage-Here a fast charge restores approximately 90 percent of
the discharged capacity,
an intermediate timed charge completes the charge and restores full
capacity, then a
maintenance charge provides a continuous trickle current to balance the
cells and compensate for
self-discharge. The fast charge (with currents in the 1C range) is
typically switched to the
intermediate charge using a temperature-sensing technique which
triggers at the onset of
overcharge. The intermediate charge normally consists of a 0.1C charge
for a timed duration
selected based on battery pack configuration. This intermediate-charge
replaces the need to fastcharge
deeply into the overcharge regime to ensure that the cell has received
a full charge.
Three-step charging, such as illustrated in Figure 20, requires greater
charger complexity (to
incorporate a second switch point and third charge rate), but reduces
cell exposure to life-limiting
overcharge.


Poprzedni Następny
Wiadomość
Spis treści
From: "szlovak" <adamkxBEZx_at_nospam_o2.pl>
Subject: Re: MAX713 i Energizer NH12
Date: Tue, 11 Apr 2006 05:30:59 +0000 (UTC)


Widzę chyba że jak nie pokażę na przykładzie to nikt z szanownych słuchaczy nie zajarzy o co chodzi.Otóż ten pdf, nie tłumaczy niczego szczególnego. Chodziło mi raczej o coś takiego : http://www.gpbatteries.com.hk/pic/91aaalh.PDF i jest tam podane i delt